Welcome to PaintRemover.com

Not sure what to order?

(800) 315-0204

free-shipping

Lead Stop Encapsulant

Lead Stop Encapsulant

Product Name Price Qty
Lead Stop Encapsulant 5 Gallons

$199.99

$387.99

Item No: 640-4000-G

Call Us

Lead Stop Encapsulant is manufactured by Dumond Chemicals. Dumond are widely recognized as market leaders in regards producing effective, environmentally safe, easy-to-use solutions to a range of professional, marine, industrial and household jobs.

If you are painting or covering over lead paint, you need to use a lead encapsulant product first. This creates a safe barrier over the surface with the lead based paint, allowing the new coatings to be applied and take well.

Lead Stop Encapsulant is Dumond’s lead paint encapsulating compound, it creates a thick elastomeric coating over the surface being treated. It will provide a long lasting, protective barrier, sealing in and blocking lead contained in the old paint.

Before applying Lead Stop Encapsulant to any surface always do a small test area. Although every effort has been made to test the product on as many surfaces as possible, it is always recommended to test the surface you will be treating.

If you require any professional advice concerning this product and its uses, please give our sales team a call.
Application Instructions: For encapsulation of lead-paint on walls, ceilings, trim and other surfaces use brush, roller or other airless piston-type spray equipment with tip size 0.015-0.023 inches (e.g., Graco Ultra 1000 Electronic Sprayer). Prior to application clean the desired surface and make sure it is dry and free of all foreign matter including dust, grease, oil, mildew, glue size, calcimine, wax, soap, loose paint, etc. Patch and repair irregularities in surfaces with prepared vinyl patch or appropriate patching compound. Do not apply the product when temperatures are below 50 degrees F. Apply Lead Stop at a rate of 125 square feet per gallon. Apply second coat if greater dry film thickness is desired. A 14 mil wet application will yield a nominal 6 mil dry film thickness. The coating should dry to the touch in approximately 4 to 6 hours. At that time a second coat may be applied if necessary. Allow up to 24 hours for final curing. At that time surface is ready to be painted.

Your Guide Will Be Downloaded Shortly

Product Description & Use: LEAD STOP® Lead Encapsulating Compound is a thick elastomeric coating that is made to be a long lasting barrier over lead based paint. When applied according to directions, LEAD STOP® provides a protective barrier coat that seals and locks in lead that is contained in old lead based paints on previously painted surfaces. LEAD STOP® has earned a seal of approval for lead abatement from D.L. Litter Laboratories and the Commonwealth of Massachusetts Encapsulation Product Performance Protocol, Department of Public Health (Reg. #DL-10019) and meets the requirements of the US Department of Housing and Urban Development (H.U.D.), which spells out a 20-year manufacturer’s warranty. This product contains Bitrex anti-ingestant.

Features & Benefits:

Provides a Protective Barrier Coat the Seals and Locks in Lead

Long Lasting • Interior and Exterior Formulation

20 Year Manufacturer’s Warranty

Has Earned the Seal of Approval from the D.L. Litter Labratories

Limitations: LEAD STOP® is not recommended for high or constant friction areas such as window sash liners or door frames. Do not apply in temperatures below 50° degrees Fahrenheit. Regulatory Information: VOC compliance - LEAD STOP® meets national, state and local regulations.

Preparation: Surfaces to be encapsulated shall be sound, free from dirt, grease, mildew, chalk and loose peeling paint. Remove loose or peeling paint by wet sanding or HEPA Vacuum dry sanding. Gloss painted surfaces should be wet sanded or prepared with a deglossing product to ensure good adhesion. Generally all surfaces should be washed thoroughly, with a suitable detergent and properly rinsed and wiped dry. All work associated with lead abatement should be done in accordance with local, state and federal regulations.

Surface and Air Temperatures: To avoid product from freezing and reducing effectiveness do not use below 35° degrees Fahrenheit. For best results, use product in temperatures above 50° degrees Fahrenheit and below 90° degrees Fahrenheit. Product effectiveness is increased in warmer temperatures.

Application & Spread Rate: In order to obtain required dry mils thickness with a single application, spraying is recommended. When applying with a roller or brush, two coats may be required. Continually monitor coating thickness with a wet mil gauge. ROLLER: use a roller with ½” nap. BRUSH: Use good quality tapered brushes. Spray Application: For best results, airless spray application should be applied in one coat of between 14-16 mils wet per coat, which provides a smooth, dry film at this level. Use a .019 to .025 inch tip orifice and a 60 mesh filter. Be sure to use an organic vapor respirator to avoi tasting the anti-ingestant.

Drying Time & Coverage: This will depend on how it is applied. If spraying to full recommended wet thickness of 14 mils in one application, then drying time will be 24 hours. However, when applying by brush or roller when two coats might be required to build up to the correct dry film thickness, the product is touch dry within an hour and re-coatable in three hours. Ambient temperature will affect drying time. Cross ventilation is important for proper drying and curing. Coverage at the maximum 7 mils dry thickness at a wet thickness of 14 mils will give a coverage rate of 125 sq. ft. to the gallon. Sensible Precautions: Close container after use. Keep out of reach of children and animals. Protect from freezing. Wash all equipment well after using.

CAUTION: Will not provide protection against lead paint once the coated surface is abraded or broken. Coated surfaces should be inspected regularly and damaged areas repaired and recoated immediately. Availability & Cost: Dumond® Chemicals products are available through a nationwide network of paint stores, hardware stores and safety supply distributors. For outlet nearest you please visit www.dumondchemicals.com once on the website type your zip code or postal code into the dealer locater to find addresses and phone numbers of your nearest dealer.

Health & Safety Requirements: Not for internal consumption. While Lead Stop™ is formulated to be safe for the user, surface and environment, proper safety procedures should be followed at all times when handling this product. Read the full label and MSDS for precautionary instructions before use. 24-Hour Emergency Information: 1-800-535-5053 North America or 1-325-323-3500 International

Save over $69 now on our environmentally friendly paint remover package including Peel Away 7 1-Gallon and Smart Strip 1-Gallon for only $129.99 and you'll see great results! PEEL AWAY® 7 is an environmentally safe paint remover used to remove oil and latex paint. Works well when removing paint from wood to be kept it's natural color after stripping. Should be used in all situations where you are looking to keep the wood in its natural form.

Smart Strip™ by Peel Away® removes 15 LAYERS OF PAINT IN ONE SINGLE APPLICATION. It is a unique paint remover that is 100% biodegradable, safe for the user, the surfaces to be stripped and the environment. Smart Strip™ by Peel Away® is very effective for removing multiple layers of paint, industrial coatings and architectural finishes from virtually all interior and exterior surfaces. Works wonders on painted brick, all kinds of wood products, metals, stone, plaster, concrete, fiberglass and much more! Great for Acrylic Paint, Latex Paint, Lead Based Paint, Oil Based Paint, Shellac, Stains, Urethane and Water Based Paints. Order Now and Save!